-
ISO 9001Certified quality system
-
CMMReports on request
Four families of UAV components, from payload and flight control hardware to motor, structural and mechanical connector parts.
UAV payload mounts, gimbal housings, camera mount frames, gimbal mount plates, sensor housings for avionics and LiDAR, IMU mounts and GPS antenna brackets.
Motor housings, bearing seats, ESC cooling plates, heat-dissipation housings and power distribution plates: parts where fit, heat path and vibration decide the result.
Lightweight aluminum structures: drone motor mounts, drone frame arms and arm fittings, landing gear mounts, center plates, mounting brackets, battery trays and standoffs.
Quick-release locks, couplers, bushings and linkage rods that join payloads, frame arms and actuators, machined to your drawing.
CMM inspection checks coaxial bores and parallel and perpendicular faces, not isolated sizes. GD&T is read to ASME Y14.5, with ISO 2768 when the drawing calls for it.
Wall thickness and pocket depth are checked to the drawing, with toolpaths, clamping and staged cutting chosen to keep thin geometry stable.
Material and lot traceability, and prototype revision control so production parts match the approved flight-test revision. FAI report on request.
Machining capabilities for UAV housings and mounts, matched to what each part needs: shared datums, thin walls, bores and flat plates.
Multi-face housings, gimbal yokes and angled motor mounts cut in fewer setups.
Pocketed payload housings and covers, with clamping chosen to keep geometry stable.
Bearing seats, shafts, standoffs, bushings and round housings for UAV assemblies.
Plates, brackets, battery trays and heat sinks milled to the drawing.
MIL-A-8625 Type II anodizing for corrosion protection and low reflection near optics.
MIL-A-8625 Type III anodizing for wear resistance on clamps, hinges and pivots.
MIL-DTL-5541 conductive, corrosion-protected surfaces for avionics housings and grounding points.
Electroless nickel plating for precision payload and wear parts, as your drawing specifies.
Laser-marked payload IDs, part numbers and revision tracking on finished parts.
Payload and avionics housings, gimbal parts, frame arms and motor mounts: the default for stiff, light, thin-walled parts.
Brackets, trays and plates where cost and corrosion resistance come first. Plate per ASTM B209, extrusions per B221.
Highly loaded pins, hinge parts, small shafts and thin fittings. Bar to ASTM B348 or AMS 4928.
Shafts, pins, sleeves and load-bearing hardware in UAV assemblies, machined to your drawing.
Insulating and heat-resistant parts placed near sensors and onboard electronics.
Low-friction bushings, spacers and pivots for moving parts of UAV mechanisms.
Insulating spacers and light, non-structural parts inside UAV assemblies.
Machined payload, gimbal, sensor, motor and structural parts from our part families, each made to the customer drawing.
Our UAV payload mounts are delivered with verified ±0.005 mm precision, reliable 4–7 day lead times, and full inspection, supporting rapid prototypes and controlled production runs.
We machine UAV gimbal housing parts to your drawing for industrial UAV and UAS programs: camera housings, yoke arms, motor housings and bearing seats of stabilized payloads. Each set is machined and inspected together.
We machine drone camera mount frames to your drawing for industrial UAV programs in mapping, survey, inspection and security. Rigid, light frames with datum faces that bring the camera back to the same position after every swap.
These professional battery trays feature +/-0.005mm precision and 4–7 days lead time. Our ISO-certified production handles rapid prototyping and mass volume, ensuring high-strength quality for critical energy storage systems.
We machine custom drone motor mounts and actuator mounts for industrial UAV programs, to your motor's bolt pattern and arm interface. Built from your drawing and motor datasheet, from flight-test sets to repeat production.
We machine custom drone arms for industrial UAV and multirotor frames: one-piece aluminum arms, root fittings, folding joints and motor-end fittings. Each is made to your drawing, from prototype arms to repeat production.
We machine drone landing gear parts to your drawing for industrial UAV and UAS programs: frame mounts, tube clamps, hinges and foot fittings. Each part fits your own frame, from the first prototype set to repeat production batches.
These professional battery trays feature +/-0.005mm precision and 4–7 days lead time. Our ISO-certified production handles rapid prototyping and mass volume, ensuring high-strength quality for critical energy storage systems.
DroneCNCParts, a division of DEK, machines payload, avionics, gimbal and motor mount hardware for industrial UAV and UAS programs, to your drawing.
Answers on what we machine, order quantities, prototype timing, quote files, quality documents and confidentiality.
Upload your CAD and 2D drawing. An engineer reviews it before machining, we sign NDAs on request, and repeat batches are built to the same inspection plan.
English
French
German
Japanese
